Hello, i ordered the driver. I have a friend who changed it.
And the machine is back online and the Y axis works fine.
So my problem is SOLVED!
Thanks for you replies, i hope this threat help someone else too.
Search found 10 matches
- Sat May 14, 2016 2:08 pm
- Forum: Electronics
- Topic: Shapeoko 2 problem with Y axis on gShield
- Replies: 6
- Views: 2030
- Fri Apr 29, 2016 6:20 pm
- Forum: Electronics
- Topic: Shapeoko 2 problem with Y axis on gShield
- Replies: 6
- Views: 2030
Re: Shapeoko 2 problem with Y axis on gShield
Thanks for the answers. I have tried to increase the y axis pot but i got the same result. I'm afraid that the driver chip is blown because i put my finger above and it's very hot - i can hold my finger above for 2 seconds only :( . The other two chips for the X and Z axis are ok - i can hold my fin...
- Fri Apr 29, 2016 9:37 am
- Forum: Electronics
- Topic: Shapeoko 2 problem with Y axis on gShield
- Replies: 6
- Views: 2030
Shapeoko 2 problem with Y axis on gShield
Hi, I have problem with moving the Y axis. The problem consist in when i try to move the Y axis, the machine makes strange move like stuttering ( tries to make some move like forward-backward and then stops ). The problem is only with the Y axis. I didn't change anything on the software or hardware....
- Tue May 12, 2015 4:43 pm
- Forum: Discussion
- Topic: Prototype Calibration Pattern (with G-Code)
- Replies: 25
- Views: 29444
Re: Prototype Calibration Pattern (with G-Code)
Hi, i have problem with squaring the machine. Tried to make this pattern and here what i found with the circles. Can someone tell me what exactly is the problem. What i have to look for for squaring right. I think that this is problem with the X and Y square but not sure. Here is the pic. https://dr...
- Thu Feb 26, 2015 9:41 pm
- Forum: Electronics
- Topic: Limit Switch Wiring?
- Replies: 102
- Views: 66270
Re: Limit Switch Wiring?
Hi again,
my grbl version is 0.8c so i saw that the hard limit comand is $16. I put it on $16=1 and it worked.
Now i must read a little more for understnding GRBL.
Thanks for the help.
my grbl version is 0.8c so i saw that the hard limit comand is $16. I put it on $16=1 and it worked.
Now i must read a little more for understnding GRBL.
Thanks for the help.
- Thu Feb 26, 2015 3:23 pm
- Forum: Electronics
- Topic: Limit Switch Wiring?
- Replies: 102
- Views: 66270
Re: Limit Switch Wiring?
Thanks for the answer!
Here is the link in google drive hope its working this time https://drive.google.com/file/d/0ByFvao ... sp=sharing
What i didn't do is to write the command to enable the limit switches. I'll try this later and i'll write how it goes.
Thank you!
Here is the link in google drive hope its working this time https://drive.google.com/file/d/0ByFvao ... sp=sharing
What i didn't do is to write the command to enable the limit switches. I'll try this later and i'll write how it goes.
Thank you!
- Thu Feb 26, 2015 1:44 pm
- Forum: Electronics
- Topic: Limit Switch Wiring?
- Replies: 102
- Views: 66270
Re: Limit Switch Wiring?
Hello, I just assembled my shapeoko 2, and now i want to put the limit switches. My shapeoko is full kit with arduino uno and gshield v5b. I have read about the limit switches and tried the schematics in this thread on the first page, but it doesn't work. I have tested with one limit switch on the X...
- Thu Feb 05, 2015 12:38 pm
- Forum: Mach3
- Topic: Considering using Mach3 with ShapeOko
- Replies: 11
- Views: 7543
Re: Considering using Mach3 with ShapeOko
Please see: http://www.shapeoko.com/wiki/index.php/Overview#Machine It is able to move using [[Stepper Motors]] which are controlled by [[Stepper Drivers]] attached to a controlling system. In the past, this had to be a full-fledged computer system which ran a G-Code interpreter, attached via speci...
- Thu Feb 05, 2015 7:56 am
- Forum: Mach3
- Topic: Considering using Mach3 with ShapeOko
- Replies: 11
- Views: 7543
Re: Considering using Mach3 with ShapeOko
Hi, i'm a newbie in the CNC machines. I want to buy Shapeoko 2 but what i don't understand is how does it work with the Mach3 software. Shapeoko 2 is with a USB connection to PC and the Mach 3 software uses Parallel port. How can i connect Shapeoko2 with Mach3 in this case? Please give me some expl...
- Tue Feb 03, 2015 9:05 pm
- Forum: Mach3
- Topic: Considering using Mach3 with ShapeOko
- Replies: 11
- Views: 7543
Re: Considering using Mach3 with ShapeOko
Hi, i'm a newbie in the CNC machines. I want to buy Shapeoko 2 but what i don't understand is how does it work with the Mach3 software. Shapeoko 2 is with a USB connection to PC and the Mach 3 software uses Parallel port. How can i connect Shapeoko2 with Mach3 in this case? Please give me some expla...