Search found 40 matches

by Ric
Sat Mar 28, 2020 2:03 am
Forum: Discussion
Topic: Upgrading S02 to 1000mm^2, advice needed.
Replies: 4
Views: 670

Re: Upgrading S02 to 1000mm^2, advice needed.

Here are a couple of photos of my machine, which is a work in progress. I still have a lot to do for the upgrade, but you asked for some photos. On the second you'll see the Nema 23 mounted with the wide Makerslide. Notice that I couldn't use all 4 mounting bolts for the Nema 23, and only used 3; th...
by Ric
Fri Mar 27, 2020 2:50 pm
Forum: Discussion
Topic: Upgrading S02 to 1000mm^2, advice needed.
Replies: 4
Views: 670

Re: Upgrading S02 to 1000mm^2, advice needed.

Yes, the wide maker slide is just for the x axis. It mounted right onto the old plates. A very easy upgrade. I did go to 9mm belts at the same time. I haven't used the machine enough to give an extended review of the upgrades yet. Once I upgraded to 1000m I realized it takes up too much room in my g...
by Ric
Thu Mar 26, 2020 2:58 pm
Forum: Discussion
Topic: Upgrading S02 to 1000mm^2, advice needed.
Replies: 4
Views: 670

Re: Upgrading S02 to 1000mm^2, advice needed.

I recently did this upgrade, and got the wide Makerslide: https://www.inventables.com/technologies/wide-makerslide If you're going to be buying two pieces of 1000m regular Makerslide, I'd go with this instead. I also got the one piece x carriage extrusion https://www.inventables.com/technologies/x-c...
by Ric
Mon Mar 02, 2020 1:59 pm
Forum: Discussion
Topic: Does Inventables Nema 23 upgrade to Shapeoko 2 work ok?
Replies: 4
Views: 2553

Re: Does Inventables Nema 23 upgrade to Shapeoko 2 work ok?

I misspoke when I said I increased the voltage; I just used the info on these pages: https://wiki.shapeoko.com/index.php/Tuning https://github.com/synthetos/grblShield/wiki/Using-grblShield#setting-motor-current I haven't actually made the controller boards mentioned in that link, so my info is not ...
by Ric
Sun Mar 01, 2020 1:36 pm
Forum: Discussion
Topic: Does Inventables Nema 23 upgrade to Shapeoko 2 work ok?
Replies: 4
Views: 2553

Re: Does Inventables Nema 23 upgrade to Shapeoko 2 work ok?

I did this upgrade recently, and although I've only made a few projects with it, I didn't need a new controller. I did find I was skipping steps at times, and had to increase the voltage a bit. I didn't change the z-axis nemo 17, and so far haven't seen a need to do so. I also upgraded to 9mm belts ...
by Ric
Wed Feb 12, 2020 8:20 pm
Forum: Design Ideas
Topic: Pulley design to lift 1000m x 1000m to ceiling
Replies: 0
Views: 3290

Pulley design to lift 1000m x 1000m to ceiling

I have a 1000mm x 1000mm shapeoko 2 that is mounted to a torsion box, and is pretty heavy. I have very little room in my garage, and want to lift it to the ceiling when it is not in use. My original plan was to use several pulleys, connected in 'series' around the Shapeoko, but that didn't work. Bas...
by Ric
Wed Oct 23, 2019 1:10 am
Forum: Discussion
Topic: T-track spacing
Replies: 2
Views: 2012

T-track spacing

I'm upgrading my Shapeoko 2 to 1000mmx1000mm. I decided to use T-track, and wonder what is the best spacing between them. On my old wasteboard, I have T-nuts spaced about 3" apart (I think), but I'm wondering if with T-track I could go 4" or even 6"? Also, I'm trying to decide how to construct the w...
by Ric
Sun Apr 07, 2019 2:31 pm
Forum: Discussion
Topic: carving wooden ducks
Replies: 3
Views: 930

Re: carving wooden ducks

Thanks for this suggestion. I watched the video, and it looks promising. The ducks are small enough that I could easily take photos from any angle. Hopefully the software doesn't require too much artistic talent, because I'm lacking in that area. So I plan to read more about this and try it, since I...
by Ric
Thu Mar 21, 2019 1:35 am
Forum: Discussion
Topic: carving wooden ducks
Replies: 3
Views: 930

carving wooden ducks

I would like to carve some Korean ducks with my shapeoko 2, but my design skills are pretty poor; I certainly am unable to draw them into Fusion360, and suspect I need to have them scanned in some way. If I can get a model of a duck into Fusion360, I was thinking I would ‘cut’ it in half, and then m...
by Ric
Wed Nov 14, 2018 5:00 pm
Forum: Discussion
Topic: controller explanation, advice needed
Replies: 1
Views: 321

controller explanation, advice needed

I have a Shapeoko 2 that is upgraded to 1000m x 1000m. I am about to upgrade to nema 23 motors and 9mm belts, and it was suggested that I might also want to upgrade the electronics to an x-controller. My understanding of the electronics on the Shapeoko 2 is about as minimal as one can get, so I'm no...