Search found 9 matches
- Tue Dec 22, 2015 1:49 am
- Forum: Discussion
- Topic: Carbide Create
- Replies: 0
- Views: 445
Carbide Create
Just downloaded carbide create and was wondering if there is a tutorial for this new software?
- Wed Sep 09, 2015 8:47 pm
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Re: Shapeoko 3 - Assembly Instructions (preliminary)
Just a quick note to those of you who have not yet assembled your oko3 yet. I wish I had installed the router bracket in the upper holes, you can drop the router down in the bracelet but you are limited as to how far you can raise the router. If you use a waste board and your work piece you could be...
- Thu Sep 03, 2015 1:40 am
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Re: Shapeoko 3 - Assembly Instructions (preliminary)
Congrats on your new purchase, just be sure you read the instructions at lest four times before even taken it out of the box!!! Have fun! This is from one who knows.
- Wed Aug 26, 2015 3:41 am
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Re: Shapeoko 3 - Assembly Instructions (preliminary)
I understand that there has been some chatter about post processor for V Carve software. where do I need to go to find the posts concerning the P/P. If I'm wrong does anyone have any thoughts on P/P for V Carve
- Wed Jul 22, 2015 3:44 pm
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Re: Shapeoko 3 - Assembly Instructions (preliminary)
concerning--Carbide Motion start up--checked all connections---still no response----My shop does not have internet access could that be a problem?
- Wed Jul 22, 2015 3:58 am
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Re: Shapeoko 3 - Assembly Instructions (preliminary)
i need help. as im new to cnc and computers i finally have my Shapeoko hooked up downloaded Carbid Motion pluged everything in clicked on C/M to jog the router around and nothing happened. not sure where to start my check list. thanks in advance!!!!
- Mon Jul 13, 2015 11:04 pm
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
motor wiring
I think they were quite vague as to the placement of the motors concering the wiring lenghts and where does the short and the long wires go, and what is the tube of liquid for?
I presume it is a thread locking liquid and used for the allen set screws.
I presume it is a thread locking liquid and used for the allen set screws.
- Tue Jun 30, 2015 12:28 am
- Forum: Software - CAD, CAM, Workflow Help
- Topic: Software design to ShapeOko 3
- Replies: 2
- Views: 782
Software design to ShapeOko 3
I'm new to all of this. I am using V Carve Pro Desktop. I need help going from software design to actual work. will appreciate the help as I've never done anything like this before. THANKS
- Mon Jun 29, 2015 11:40 pm
- Forum: Shapeoko 3 Assembly
- Topic: Shapeoko 3 - Assembly Instructions (preliminary)
- Replies: 86
- Views: 59046
Shapeoko 3 startup
im new to all of that has to do with software and forums. So i need HELP. where do I go for help with going from software (V Carve Pro Desktop) to my Shapeoko 3 router?