Here:
http://www.shapeoko.com/wiki/index.php/ ... 6_Hardware
But am stumped as to where it would go in the sidebar --- perhaps under ``Gallery''?
It'd be great if everyone would share any suggestions or examples which they might have --- items should be:
- joints suited for cutting w/ a mill
- hardware which can be used w/ mounting points cut w/ a mill
- other?
add a page for ``Fabrication Techniques & Hardware''
-
- Posts: 8542
- Joined: Mon Apr 09, 2012 6:11 pm
- Location: Pennsylvania --- south of the Turnpike, East of US-15
- Contact:
add a page for ``Fabrication Techniques & Hardware''
Shapeoko 3XL #0006 w/ Carbide Compact Router w/0.125″ and ¼″ Carbide 3D precision collets
Nomad 883 Pro #596 (bamboo)
Nomad 883 Pro #596 (bamboo)
Re: add a page for ``Fabrication Techniques & Hardware''
I added a link to the 50 Digital Wood Joints project. If you haven't looked through it yet, you will be amazed. It is a fantastic resource.
I'd like to have the zip file containing the joints hosted in the wiki (just in case the original disappears), what's the best way to do this? Github?
I'd like to have the zip file containing the joints hosted in the wiki (just in case the original disappears), what's the best way to do this? Github?
Re: add a page for ``Fabrication Techniques & Hardware''
I'm having a formatting issue. The "Hardware" is showing beside the image, I want it under. What am I doing wrong?
And I noticed you already had the link. I'm apparantly not very good at reading today.
As for location, maybe move it under "Using Your Machine"?
And I noticed you already had the link. I'm apparantly not very good at reading today.
As for location, maybe move it under "Using Your Machine"?
-
- Posts: 8542
- Joined: Mon Apr 09, 2012 6:11 pm
- Location: Pennsylvania --- south of the Turnpike, East of US-15
- Contact:
Re: add a page for ``Fabrication Techniques & Hardware''
putting it in a frame makes it float --- turn that off:Enraged wrote:I'm having a formatting issue. The "Hardware" is showing beside the image, I want it under. What am I doing wrong?
[[ Image: 50_Digital_Wood_Joints.jpg | 200px | 50 Digital Wood Joints by Jochen Gros]]
Maybe a little further down into Gallery? There's already a lot in ``Using Your Machine'', and joints won't apply to people using drag knives, 3D printers, &c.And I noticed you already had the link. I'm apparantly not very good at reading today.
As for location, maybe move it under "Using Your Machine"?
Shapeoko 3XL #0006 w/ Carbide Compact Router w/0.125″ and ¼″ Carbide 3D precision collets
Nomad 883 Pro #596 (bamboo)
Nomad 883 Pro #596 (bamboo)
Re: add a page for ``Fabrication Techniques & Hardware''
Thanks, fixed it.
That's a good point about the Gallery. It would be easier to find.
That's a good point about the Gallery. It would be easier to find.
-
- Posts: 8542
- Joined: Mon Apr 09, 2012 6:11 pm
- Location: Pennsylvania --- south of the Turnpike, East of US-15
- Contact:
Re: add a page for ``Fabrication Techniques & Hardware''
I also added a section on Finishing --- hopefully that won't become controversial --- just want to add techniques specific to finishing up CNC-specific techniques such as V-engraving.
Shapeoko 3XL #0006 w/ Carbide Compact Router w/0.125″ and ¼″ Carbide 3D precision collets
Nomad 883 Pro #596 (bamboo)
Nomad 883 Pro #596 (bamboo)