Designing my own handheld console

Share your Shapeoko created projects!
Post Reply
xfredericox
Posts: 292
Joined: Mon May 04, 2015 10:46 am

Designing my own handheld console

Post by xfredericox » Thu Apr 13, 2017 4:28 pm

Read all about it here:
http://www.manmademayhem.com/?p=2647
Attachments
2017-04-12 21.59.13.jpg
2017-04-12 21.59.13.jpg (374.95 KiB) Viewed 1618 times
Visit my blog for updates on my current SO2/lasercutting/... projects.
http://www.manmademayhem.com

JeromyReno
Posts: 225
Joined: Mon May 04, 2015 11:28 pm

Re: Designing my own handheld console

Post by JeromyReno » Mon Apr 17, 2017 10:14 pm

rad

xfredericox
Posts: 292
Joined: Mon May 04, 2015 10:46 am

Re: Designing my own handheld console

Post by xfredericox » Wed Apr 19, 2017 3:35 pm

Attachments
2017-04-18 11.31.09.jpg
2017-04-18 11.31.09.jpg (336.11 KiB) Viewed 1510 times
Visit my blog for updates on my current SO2/lasercutting/... projects.
http://www.manmademayhem.com

xfredericox
Posts: 292
Joined: Mon May 04, 2015 10:46 am

Re: Designing my own handheld console

Post by xfredericox » Sun May 07, 2017 3:58 pm

I can finally consider this one DONE.

http://www.manmademayhem.com/?p=2703

But I know there's already a lot of room for improvement... :grin:
Attachments
2017-05-07 16.34.40.jpg
2017-05-07 16.34.40.jpg (321.95 KiB) Viewed 1393 times
Visit my blog for updates on my current SO2/lasercutting/... projects.
http://www.manmademayhem.com

RaymondOverman
Posts: 50
Joined: Tue May 20, 2014 8:13 pm

Re: Designing my own handheld console

Post by RaymondOverman » Fri May 19, 2017 8:00 pm

Very impressive build. Great job.
SO2 / NEMA 23s / 5 axis SainSmart BOB and Drivers / DW660 Spindle / Rotary Axis / Spindle-Vac Relay / LimSW / Fender Wells / Drilled and Tapped 1"x8TPI Waste Board

JeromyReno
Posts: 225
Joined: Mon May 04, 2015 11:28 pm

Re: Designing my own handheld console

Post by JeromyReno » Tue May 30, 2017 8:38 pm

THIS IS SO SICK!!

LynsaintT
Posts: 2
Joined: Thu Jun 01, 2017 7:41 pm

Re: Designing my own handheld console

Post by LynsaintT » Thu Jun 01, 2017 8:11 pm

Wow that fits perfectly. A wood touch to a modern finish.

xfredericox
Posts: 292
Joined: Mon May 04, 2015 10:46 am

Re: Designing my own handheld console

Post by xfredericox » Sun Jun 04, 2017 12:33 pm

thanks guys.

It was a very rewarding project!
Visit my blog for updates on my current SO2/lasercutting/... projects.
http://www.manmademayhem.com

Post Reply