nema 17 heat problem

Post Reply
op117
Posts: 8
Joined: Fri Jun 12, 2015 12:48 pm

nema 17 heat problem

Post by op117 » Sat Jun 13, 2015 2:24 am

whats the best way to cool down the nema 17 motors?
The ambient temp is around 90F and i have thermal shut at every job, also cooling the air is not a potion for my shop at the moment...

whats the best heat sinks, fans , and config of eater... would be awesome to put a radiator like a h100 with custom blocks on the motors :o :lol:

but whats the most cost effected cooling for this :?:

WillAdams
Posts: 8533
Joined: Mon Apr 09, 2012 6:11 pm
Location: Pennsylvania --- south of the Turnpike, East of US-15
Contact:

Re: nema 17 heat problem

Post by WillAdams » Sat Jun 13, 2015 3:25 am

Are you certain it’s the motors shutting down and not the stepper drivers?

- active cooling --- get a fan
- adjust the current, turn it down as much as makes sense

http://www.shapeoko.com/wiki/index.php/ ... he_Current
Shapeoko 3XL #0006 w/Makita RT0701 Router w/0.125″ and ¼″ Elaire precision collets
Nomad 883 Pro #596 (bamboo)

Jimf
Posts: 233
Joined: Wed Feb 11, 2015 8:58 pm

nema 17 heat problem

Post by Jimf » Sat Jun 13, 2015 3:52 am

I use small 12volt fans attached to heat sinks. The ones you see used on graphics card.s. They will lower the temperature approximately 20 degrees.

clockit
Posts: 319
Joined: Sun Nov 16, 2014 11:05 pm
Location: California, MO

Re: nema 17 heat problem

Post by clockit » Sat Jun 13, 2015 5:28 am

I'm with Will here, I've cut jobs that lasted over 2 hours and never once have my 17's shut down...
Shapeoko 2, Full Kit #7071, Makita RT0701C Router, 1000 x 1000 upgrade, Acme Z Axis w/Nema 17 Belt Drive

op117
Posts: 8
Joined: Fri Jun 12, 2015 12:48 pm

Re: nema 17 heat problem

Post by op117 » Sat Jun 13, 2015 6:06 am

im thinking of getting

heatsinks
4x http://www.amazon.com/gp/product/B00N41 ... W35WSKZ6W8

cutting to size for motor driver board and the motos thim selfs and

2x http://www.amazon.com/40mmx10mm-Blades- ... +40mm+fans

fans

also i have all ready adjusted the pots on the driver board, but still gettting a shut down....

this is just for fun i made a inventer file for a nema 17 water block:
http://www.filedropper.com/nema17waterblock :lol:

cvoinescu
Posts: 4442
Joined: Thu Jul 19, 2012 6:50 pm
Location: Camberley, UK
Contact:

Re: nema 17 heat problem

Post by cvoinescu » Mon Jun 15, 2015 6:58 pm

The motors themselves do not have any sort of temperature sensing or overheating cut-out. They can go fairly hot (hotter than you can keep a finger on for more than a second) before they're in danger. If they cut out, it's the drivers that overheat, and cooling the motors will not make a difference. You can reduce the current a little to reduce the motor and driver temperature, but it also reduces torque. What you need is better cooling of your drivers (gShield or whatever you're using). Try to get airflow both over and under the board (e.g. with a fan placed to one side).
Proud owner of ShapeOko #709, eShapeOko #0, and of store.amberspyglass.co.uk

Post Reply