ShapeOko #1508 Build Log

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Re: Pre-Shapeoko #XXXX Build Log

Post by LTMNO » Thu Apr 18, 2013 8:41 pm

The build for the motor mounts etc has started... its probably good to note for anyone in the future that if you are using Nema23's instead of the 17's that the (4x) 5mm x 10mm bolts will not be enough with the washers and such to connect the nuts on the other end.

You will need a longer bolt more like 14-15mm to be safe.

That might have been said somewhere and I didn't catch it when ordering from Inventables.

Just to note as its my first hick-up on the build.

Also,
The eccentric spacers are not sitting flush.... I will have to drill the holes out a bit more with 9/32 bit thanks to IC for the info.
photo 2.1.jpg
photo 2.1.jpg (98.99 KiB) Viewed 1821 times
photo 1.1.jpg
photo 1.1.jpg (103.39 KiB) Viewed 1821 times
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Shapeoko #XXXX Build Log

Post by LTMNO » Sat Apr 20, 2013 1:45 pm

Silly question here, how do you know what ShapeOko ### you are? I don't see anything on the Invoice, etc.

Thanks.
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

WillAdams
Posts: 8488
Joined: Mon Apr 09, 2012 6:11 pm
Location: Pennsylvania --- south of the Turnpike, East of US-15
Contact:

Re: Shapeoko #XXXX Build Log

Post by WillAdams » Sat Apr 20, 2013 2:14 pm

Send a message to Edward to get a serial number.
Shapeoko 3XL #0006 w/Makita RT0701 Router w/0.125″ and ¼″ Elaire precision collets
Nomad 883 Pro #596 (bamboo)

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Re: Shapeoko #XXXX Build Log

Post by LTMNO » Sat Apr 20, 2013 3:38 pm

thanks, much obliged.
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Re: Shapeoko #XXXX Build Log

Post by LTMNO » Sat Apr 20, 2013 3:39 pm

update - sanded all panels, drilled all 9/32 holes and now ready for paint.
off to the hardware store for some primer and paint.

update - primer coat on, will let it cure til tomorrow for the good coat of Burnt Rust, love that colour.
My attempt of a paint room. I have my shop vac at the bottom sucking all the overspray. It actually worked pretty good.
IMG_2692.jpeg
IMG_2692.jpeg (79.19 KiB) Viewed 1787 times
Update : Final coat of Rusty Orange...
IMG_2701.jpg
IMG_2701.jpg (80.47 KiB) Viewed 1747 times
IMG_2697.jpg
The Paint Room Setup
IMG_2697.jpg (95.39 KiB) Viewed 1747 times
Last edited by LTMNO on Tue Apr 23, 2013 8:20 pm, edited 1 time in total.
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Canada's ShapeOko Count (+1)

Post by LTMNO » Tue Apr 23, 2013 8:16 pm

Canada's ShapeOko Count (+1)
IMG_2704.jpg
IMG_2704.jpg (98.67 KiB) Viewed 1747 times
IMG_2702.jpg
IMG_2702.jpg (135.94 KiB) Viewed 1747 times
Its finally done Mechanically. On to the electronics and adding the Belts. I didn't seem to get how to install the Belts with what was provided. I didn't want to just a use the Tie-Straps.
I am going to the hardware store tonight to get something else based on other ShapeOko Successes (thanks to the wiki)

I do however have a few extra parts which is always alarming. I assume from ordering the Z-axis upgrade Kit and the Dual X-Axis Kit and not using the Nema 17's would be the cause. I have attached the list if someone should think otherwise.

Extra Remaining parts…

8x ¼” Nylon Spacer (SM-H01)
14x ¾” Nylon Spacer (SM-H02)

2x Insertion Nuts (SM-H11) (4 were for the Motor Mounts on Z-Axis)

18x M3 Flat Washers (for Nema 17)
18x M3 x 6mm SHCS (for Nema 17)
3x M3 x 50mm SHCS (SM-H06) (for Nema 17)

6x M5 x 10mm SHCS
3x M5 x 16mm SHCS (SM-H13)
2x M5 x 20mm SHCS
8x M5 x 30mm SHCS (SM-H08)
4x M5 x 55mm SHCS (SM-H09)

2x M8 Hex Nut (SM-H10) (For Z-Axis Original)
2x Z-Mount Plate w/ Bearing (For Z-Axis Original)
1x Z-Coupler for Nema17 (For Z-Axis Original)
2x Spacers (For Z-Axis Original)

2x 5mm Pulley (MSK01-09) (For Nema17's, 1 for X and 1 for Y)

2x Spindle Mount Blocks/Straps (Standard Issue)

I need to order a power supply and figure out with the help of the wiki how to get this TinyG going. ;-)

Stay tuned.
Last edited by LTMNO on Wed Apr 24, 2013 2:37 am, edited 1 time in total.
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

dointhangs
Posts: 179
Joined: Tue Jun 05, 2012 7:31 pm

Re: Shapeoko #XXXX Build Log

Post by dointhangs » Tue Apr 23, 2013 9:43 pm

I absolutely love this color and the nema23's look so killer!! You are nailing it so far! Not sure why you have the leftover pieces but if you turn it on and it shakes itself into a pile of rubble you will know you forgot something
Shapeoko #298, dual drive upgrade, acme z axis, open bed endplates and a slightly larger ("expanded desktop") work area!

bjbsquared
Posts: 102
Joined: Mon Nov 26, 2012 10:48 am

Re: Shapeoko #XXXX Build Log

Post by bjbsquared » Wed Apr 24, 2013 12:56 am

Yep, awesome color. It goes well with the cedar? dresser in the background.
#1016 - 1M x 1M Y: Dual Motor Drive w/Looped Belts, X:Dual Rail with wlanfox blocks, Z: Stock, Spindle:DW660

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Re: Shapeoko #XXXX Build Log

Post by LTMNO » Wed Apr 24, 2013 2:29 am

dointhangs wrote:I absolutely love this color and the nema23's look so killer!! You are nailing it so far! Not sure why you have the leftover pieces but if you turn it on and it shakes itself into a pile of rubble you will know you forgot something
Ha, that is funny, I hope not... With all the Lock-Tite on there, it would have to be an earthquake. ;-)

Thanks for the post. I enjoy the colour too. ;-)
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

LTMNO
Posts: 172
Joined: Sat Mar 09, 2013 2:56 am

Re: Shapeoko #XXXX Build Log

Post by LTMNO » Wed Apr 24, 2013 2:30 am

bjbsquared wrote:Yep, awesome color. It goes well with the cedar? dresser in the background.
Thanks, I just got notice that the Chain drag has arrived.
Hopefully I can get the power supply tomorrow and get this talking... Hello World!
Cheers.
ShapeOko #1508, TinyG Controller, Dual Y, ACME Z-Axis, MeanWell(S-350-24v), NEMA 23's, 1m Squared t-slot table, OpenRail and the Original Z Makerslide and all Motor Plates...

Post Reply