Page 2 of 3

Re: NoProblem Log

Posted: Fri Apr 04, 2014 12:26 am
by noproblem
Ruwan

Bought them from Misumi
http://us.misumi-ec.com/vona2/detail/11 ... -15250-500

Part Number HFSQN4-15250-500
Price $ 27.99 each ( shipping cost not sure yet, as I haven't received to final invoice )

Marvin

Re: NoProblem Log

Posted: Fri Apr 04, 2014 3:13 am
by MeanderBolt
Wait, you have the part in hand, and have not yet been charged for the shipping? Ha.
Yes sir, that's 29 ea. and 280 shipping and handling.

Re: NoProblem Log

Posted: Fri Apr 04, 2014 6:15 am
by janapriya
Thanks Marvin

Re: NoProblem Log

Posted: Fri Apr 04, 2014 6:14 pm
by edwardrford
As a reference for the shipping. My charge was about $15. That's for their standard delivery service (UPS) and it shows up next day for me.

The way it works is: they authorize your card for the amount of the product, when they get a delivery confirmation from UPS, they run your card for the product + shipping cost.

Right, wrong, or indifferent, when ordering from industrial suppliers, this is the status quo.


-Edward

Re: NoProblem Log

Posted: Mon Apr 07, 2014 6:26 pm
by scott216
janapriya wrote:Marvin,
From where did you buy extrusions for the bed?
Ruwan.
I think he got it here: http://us.misumi-ec.com/vona2/detail/110302261820/

Re: NoProblem Log

Posted: Mon Apr 07, 2014 6:28 pm
by scott216
noproblem wrote:Nigel

Correct here is the link to the USB Borescope Endoscope Camera i bought http://www.ebay.com/itm/141214106067
That's pretty cool. How is the quality?

Re: NoProblem Log

Posted: Mon Apr 07, 2014 7:05 pm
by noproblem
The picture quality is OK is not great at far distance but at close is not bad . ( its made to close distances)

I am going to mount mine very close to the spindle just through hole on top of the dust cover. So It should work perfectly

Some guys review
http://youtu.be/ee7Pr4XsDGw

Re: NoProblem Log

Posted: Thu Apr 10, 2014 9:50 am
by Nigel K Tolley
I've got a non USB version that is exactly the same camera on a wire with a stereo jack plug for a small battery powered monitor. Very handy sometimes.

I might get one with a longer reach though, & USB would be good for some stuff. Thanks for the link.

Sent from my SM-N9005 using Tapatalk

Re: NoProblem Log

Posted: Fri Apr 11, 2014 2:31 pm
by noproblem
Actual Build Update

Here goes

Almost Finished did some quick mods

Only used one bolt and push it all the way up to the top of the plate on both Y axis. This approach increase my Z by about 25 mm
- Painted the plates ( didn't wait for it to dry properly and it got A LOT of paint got messed up.) Need to redo

More to come

Re: NoProblem Log

Posted: Sun Apr 20, 2014 10:20 pm
by noproblem
Did some work this weekend

- Mounted laser (for cutting and engraving)
- Cut and mounted an acrylic terminal wire guard
- Increased the z axis by 25mm
- Mounted spindle

To do this week
- clean up wiring some more
- wire laser to power supply and shield
- mount USB boroscope camera
- mount USB Web camera
- mount cross hair laser
- mount limit switches
- design and cut dust shoe
- wire electronics in enclosure